<?xml version="1.0" encoding="UTF-8"?>        <rss version="2.0"
             xmlns:atom="http://www.w3.org/2005/Atom"
             xmlns:dc="http://purl.org/dc/elements/1.1/"
             xmlns:sy="http://purl.org/rss/1.0/modules/syndication/"
             xmlns:admin="http://webns.net/mvcb/"
             xmlns:rdf="http://www.w3.org/1999/02/22-rdf-syntax-ns#"
             xmlns:content="http://purl.org/rss/1.0/modules/content/">
        <channel>
            <title>
									problems about RS232 - Communications				            </title>
            <link>https://www.animatics.com/forum/communications/problems-about-rs232/</link>
            <description>Animatics Distributor Locator Discussion Board</description>
            <language>en-US</language>
            <lastBuildDate>Mon, 09 Mar 2026 15:33:17 +0000</lastBuildDate>
            <generator>wpForo</generator>
            <ttl>60</ttl>
							                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-962</link>
                        <pubDate>Thu, 16 Oct 2014 23:42:07 +0000</pubDate>
                        <description><![CDATA[The following link has a page with tabs... manuals and sample programs... etc.

Note: To properly compile for your motor in the SMI2 software... Click on the Compile Menu... then select &quot;c...]]></description>
                        <content:encoded><![CDATA[The following link has a page with tabs... manuals and sample programs... etc.
http://www.animatics.com/legacy-downloads.html?task=view

Note: To properly compile for your motor in the SMI2 software... Click on the Compile Menu... then select "compiler default firmware version".  You will get a list.  Select 478T.  This version will understand the command set for your motor.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>csearcy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-962</guid>
                    </item>
				                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-961</link>
                        <pubDate>Thu, 16 Oct 2014 23:42:07 +0000</pubDate>
                        <description><![CDATA[The following link has a page with tabs... manuals and sample programs... etc. ..for your motor.


Note: To properly compile for your motor in the SMI2 software... Click on the Compile Me...]]></description>
                        <content:encoded><![CDATA[The following link has a page with tabs... manuals and sample programs... etc. ..for your motor.

http://www.animatics.com/legacy-downloads.html?task=view

Note: To properly compile for your motor in the SMI2 software... Click on the Compile Menu... then select "compiler default firmware version".  You will get a list.  Select 478T.  This version will understand the command set for your motor.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>csearcy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-961</guid>
                    </item>
				                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-960</link>
                        <pubDate>Thu, 16 Oct 2014 23:24:49 +0000</pubDate>
                        <description><![CDATA[ok... So if you type RP in the blue terminal window... you get a response from the motor? ...and if it&#039;s 0 ...you can turn the shaft and type RP again... and get a different number?

Make ...]]></description>
                        <content:encoded><![CDATA[ok... So if you type RP in the blue terminal window... you get a response from the motor? ...and if it's 0 ...you can turn the shaft and type RP again... and get a different number?

Make sure you have the latest version of SMI2 software from www.animatics.com

You may just need to either put the following commands in a program and download it to the motor... or type them in the blue terminal window...

UCI
UDI
ZS

...and to make the shaft move one revolution... type the following...

MP
A=100
V=100000
D=4000
G

...if you make a program.. it must also include an END command.  The TWAIT command can be used in a program to pause program until the current move completes.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>csearcy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-960</guid>
                    </item>
				                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-959</link>
                        <pubDate>Thu, 16 Oct 2014 23:17:49 +0000</pubDate>
                        <description><![CDATA[Yes, i do that. And i am sure I can get message when i connected 3-pin and 4-pin. The SERVO-AMPLIFIER LED is red. AND another led isn&#039;t lighting.]]></description>
                        <content:encoded><![CDATA[Yes, i do that. And i am sure I can get message when i connected 3-pin and 4-pin. The SERVO-AMPLIFIER LED is red. AND another led isn't lighting.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>Jimmy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-959</guid>
                    </item>
				                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-958</link>
                        <pubDate>Thu, 16 Oct 2014 23:04:33 +0000</pubDate>
                        <description><![CDATA[You should have the following...
pin 2 on the 9-pin D-Sub connected to pin 3 on the 7W2.
pin 3 on the 9-pin D-Sub connected to pin 4 on the 7W2.
pin 5 on the 9-pin D-Sub connected to pin ...]]></description>
                        <content:encoded><![CDATA[You should have the following...
pin 2 on the 9-pin D-Sub connected to pin 3 on the 7W2.
pin 3 on the 9-pin D-Sub connected to pin 4 on the 7W2.
pin 5 on the 9-pin D-Sub connected to pin 5 on the 7W2.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>csearcy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-958</guid>
                    </item>
				                    <item>
                        <title>problems about RS232</title>
                        <link>https://www.animatics.com/forum/communications/problems-about-rs232/#post-247</link>
                        <pubDate>Thu, 16 Oct 2014 22:52:20 +0000</pubDate>
                        <description><![CDATA[Hello my dears,
    I tried to communicate with SmartMotor(the model is SM3146DDEBRSEV, version is 4.78AE)by RS232 in using SMI software. I used 3-pin and 4-pin in 7W2 Combo D-sub to connec...]]></description>
                        <content:encoded><![CDATA[Hello my dears,
    I tried to communicate with SmartMotor(the model is SM3146DDEBRSEV, version is 4.78AE)by RS232 in using SMI software. I used 3-pin and 4-pin in 7W2 Combo D-sub to connect to my PC. I have tried these two methods in （http://cn.animatics.com/forum/communications/1401-rs232-problem-comunication.html）， but it didn't work. Now I don't know what should I do. Please help me.]]></content:encoded>
						                            <category domain="https://www.animatics.com/forum/communications/">Communications</category>                        <dc:creator>Jimmy</dc:creator>
                        <guid isPermaLink="true">https://www.animatics.com/forum/communications/problems-about-rs232/#post-247</guid>
                    </item>
							        </channel>
        </rss>
		